The Fundamentals of Plumbing Skills When Installing a Bathtub
The Fundamentals of Plumbing Skills When Installing a Bathtub
Blog Article
Nearly everybody is bound to have their personal idea involving How to Install a Bathtub.
Mounting a tub isn't exactly brain surgery, yet it does require strong plumbing, carpentry, and sometimes, tiling abilities. Replacing an old bath tub with a new one is likewise a reasonably hard job. If the old bathtub is conveniently accessible, the project can relocate speedily; if you have to open up a wall surface to get rid of the old tub and also place the brand-new bathtub, the task is a lot harder. In either situation, the task is within a house handyman's abilities, although you will require a helper to move out the old bathtub as well as set in the new one. Ensure you have qualified yourself for the work as well as fit trying it. Rather than working with a contractor to take control of a halfway-completed project, it is far better to take into consideration employing one prior to you start. Opportunities are you might need a specialist plumber to make tube connections.
This write-up will certainly aid you mount a new bath tub in your shower room if you have actually already bought a brand-new bathtub and don't require to alter the plan of your previous water system pipelines.
Your tools and also product checklist must consist of the following:
Getting ready for the Setup
First of all, the sustaining structure supplied with the bathroom should be fitted (if required) according to the supplier's guidelines. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is very important to see to it that if the faucet features a plastic washing machine, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the faucets device to stop stress on the tub.
Fit the versatile faucet ports to the bottom of the two faucets using 2 nuts and olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet via the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make sure you utilize every one of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bath should currently be ready to be fitted in its final setting.
Removing Old Touches
If you require to change old faucets with new ones as a part of your installment, after that the first thing you ought to do is disconnect the water supply. After doing so, switch on the faucets to drain any water remaining in the system. The procedure of getting rid of the existing faucets can be quite problematic due to the limited access that is typically the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the taps. Have a towel ready for the continuing to be water that will certainly come from the pipes. When the supply pipes have actually been removed, utilize the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary taps from turning during this procedure. As soon as the taps have actually been removed, the holes in the bath/basin will certainly need to be cleansed of any kind of old sealing compound.
Before going on to fit the new taps, compare the pipe connections on the old taps to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Setting up the Bath tub
Using both wood boards under its feet, put the tub in the called for setting. The wood boards are handy in evenly spreading the weight of the tub over the location of the boards rather than focusing all the weight onto four little points.
The next goal is to ensure that the bathtub is leveled all round. This can be attained by examining the spirit level and also changing the feet on the tub until the spirit level reads degree.
To mount taps, fit the bottom of the furthest flexible faucet adapter to the proper supply pipe by making a compression join; after that do the very same for the other faucet.
Turn on the water system as well as check all joints and also new pipework for leaks as well as tighten them if required. Fill the bath tub as well as additionally inspect the overflow outlet and also the regular electrical outlet for leaks.
Lastly, fix the bath paneling as defined in the manufacturer's instruction manual. Tiling and securing around the tub ought to wait till the bath tub has actually been used a minimum of when as this will settle it right into its last placement.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will require a plastic adapter to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet as well as the various other end offers a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly require reducing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the placing opening in the bath/basin making sure that the washing machines remain in area in between the faucet as well as the sink. Protect the faucet in place with the manufacturer provided backnut. As soon as the tap is safely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with typical tap ports. The previous type needs to be connected to the faucet ends initially, tightening up just by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the location where the bathroom satisfies the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the fitting can relocate enough to split a stiff seal, causing the water to pass through the wall in between the bath and the tiling, resulting in difficulties with wetness and also feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to blend in your fixtures as well as installations. They are sold in tubes as well as cartridges, as well as can sealing spaces up to a size of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with twists of soaked newspaper or soft rope. Bear in mind to always fill the bathtub with water prior to sealing, to allow for the motion experienced when the bathtub remains in use. The sealer can split relatively early if you do not take into consideration this activity before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise easily offered on the market. It is a good idea to fit the floor tiles making use of water-resistant or waterproof adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We are very excited about Tools You Need to Install a New Bathtub and I am assuming you liked the article. Do you know about another person who is involved in the niche? Feel free to promote it. Thank you so much for going through it.
Need urgent help? Reach. Report this page